Usbasp V2 0 Driver Windows 10

Download Driver Usbasp V2 0 Windows 10
Usbasp Drivers
Usbasp V2 0 Driver Windows 10 Windows 7
Lc Technology Usbasp V2.0 Driver

USBasp driver for Windows 10 – Working solution June 28, 2017 July 17, 2020 Yesterday I’ve spent like 2 hours fighting to make USBasp ISP programmer work under Windows 10 64bit. How to install Usbasp Driver in Windows 8.1 and Windows 10. Mini atmel avr isp v2.0 stk500 usb isp programmer, 1, usb cable, 1, 10-pin idc isp cable, 1, 10-pin to 6-pin idc isp cable, 1, eccn/hts. Special note on skill level, this is a simple soldering kit, but arduino as isp is a relatively immature process, and there are some rough edges.

Help! I've spent the last couple of hours banging my head against the wall. I was trying to update my firmware with my new usbasp programmer, and have only managed to erase my chip.

I bought the programmer off ebay (it says USBASP V2.0 - LC Technology), and wired an adapter cable with the following mappings (from Sanguino to programmer):

1 - 9 (MISO)
2 - 2 (VCC)
3 - 7 (SCK)
4 - 1 (MOSI)
5 - 5 (CS)
6 - 10 (GND)

When using, it, the 1284p is detected and has the correct signature, and I can successfully read and change the fuses, so the connection seems okay. However, when trying to upload a bootloader or marlin build, it always fails to verify as follows. Any ideas? The programmer itself only has a jumper for 3.3/5V (currently set to 5V).

>avrdude -C ..etcavrdude.conf -c usbasp -p m1284p -U flash:w:SolidoodleMarlin.cpp.hex -v -D

System wide configuration file is '..etcavrdude.conf'

Using Port : lpt1
Using Programmer : usbasp
AVR Part : ATMEGA1284P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Download Driver Usbasp V2 0 Windows 10

Block Poll Page
Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW Max
W ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ---
-- ---------
eeprom 65 10 128 0 no 4096 8 0 9000 90
00 0xff 0xff
flash 65 10 256 0 yes 131072 256 512 4500 45
00 0xff 0xff
lock 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 90
00 0x00 0x00
signature 0 0 0 0 no 3 0 0 0
0 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0
0 0x00 0x00

Programmer Type : usbasp
Description : USBasp, http://www.fischl.de/usbasp/

Usbasp Drivers

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

Usbasp V2 0 Driver Windows 10 Windows 7

avrdude: Device signature = 0x1e9705
avrdude: safemode: lfuse reads as DE
avrdude: safemode: hfuse reads as DB
avrdude: safemode: efuse reads as F8
avrdude: reading input file 'SolidoodleMarlin.cpp.hex'
avrdude: input file SolidoodleMarlin.cpp.hex auto detected as Intel Hex
avrdude: writing flash (110734 bytes):

Lc Technology Usbasp V2.0 Driver

Writing | ################################################## | 100% 59.31s

avrdude: 110734 bytes of flash written
avrdude: verifying flash memory against SolidoodleMarlin.cpp.hex:
avrdude: load data flash data from input file SolidoodleMarlin.cpp.hex:
avrdude: input file SolidoodleMarlin.cpp.hex auto detected as Intel Hex
avrdude: input file SolidoodleMarlin.cpp.hex contains 110734 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 57.39s

avrdude: verifying ...
avrdude: verification error, first mismatch at byte 0x0000
0x0c != 0x00
avrdude: verification error; content mismatch

avrdude: safemode: lfuse reads as DE
avrdude: safemode: hfuse reads as DB
avrdude: safemode: efuse reads as F8
avrdude: safemode: Fuses OK

avrdude done. Thank you.